Scanning Long Pages (iX1600/iX1500)

ScanSnap Connect Application can be used to scan a long page documents such as long receipts.

The document length that can be scanned varies depending on the setting for [Scanning side] under [Scanning] in [Profile].

Scanning Side	Document Length
Duplex Scan	863 mm (33.97 in.)
Simplex Scan	1,726 mm (67.95 in.)

For details about documents that can be scanned, refer to Documents That Can Be Loaded Directly into iX1600/iX1500.

The procedure to scan a long page document is as follows:

Open the ADF paper chute (cover) of iX1600 or iX1500.
Pull out the extension and stacker on the ADF paper chute (cover).
Tap on the [File List] screen or do the same thing on the folder screen with the ScanSnap Sync function set to on.

The [Settings] screen appears.
Tap [Profile] in the [Settings] screen.

Available profiles appear.
Select [Manual Scan] for [Feed] in [Scanning].
Perform one of the following to return to the [File List] screen or the folder screen with the ScanSnap Sync function set to on.
- Press the back button on the hardware
- Tap the [Back] button on the software
The [File List] screen or the folder screen with the ScanSnap Sync function set to on appears.
Load only one document in the ADF paper chute (cover).

Load the document face-down and top-first with the back of the document facing you. Hold the document with your hand so that it does not fall out of the ADF paper chute (cover).

ATTENTION
Automatic image rotation is not available when scanning with ScanSnap Connect Application.
Adjust the side guides to both edges of the document.

Hold each side guide in the middle to adjust them. Otherwise, the documents may be fed skewed.
Perform a scan.
- To scan from ScanSnap Connect Application
  
  Tap on the [File List] screen or do the same thing on the folder screen with the ScanSnap Sync function set to on.
- To scan from iX1600/iX1500
  
  Press the [Scan] button in the home screen on the touch panel.
Finish scanning.
- To finish scanning with ScanSnap Connect Application
  
  Tap the [Exit] button.
- To finish scanning with iX1600/iX1500
  
  Press the [Finish] button on the touch panel.
A message appears indicating that the file is being received.

The received file will appear on the [File List] screen or the [Files] screen.
HINT
- You can change the setting for [Feed] by pressing the feed mode setting icon in the lower right of the screen for continuing a scan on the touch panel of iX1600 or iX1500.
  
  When you scan multiple documents such as office paper, select [Continuous Scan] for [Feed].
- When you configure [Specify destination] for [Destination] in the [Profile] screen, the file is moved to the specified destination after scanning.
  
  Because the file that is moved is not displayed in the [File List] screen or in the folder screen with the ScanSnap Sync function set to on, use another application to confirm that the image data meets your requirements.
- When the ScanSnap Sync function is set to on, the received file is uploaded to a synced cloud service automatically if you select the [Auto Upload] checkbox in [ScanSnap Sync Setting] and an Internet connection is established.
Tap the received file on the [File List] screen or the [Files] screen.

The [Preview] screen appears.
Confirm that the image data meets your requirements.

HINT
You can send and view the received file in another application. When the ScanSnap Sync function is set to on, the received file can be uploaded to a cloud service.

ATTENTION

The scanned data will be discarded if you exit ScanSnap Connect Application during scanning.
When a notification occurs such as an e-mail alert, alarm or power shortage, a mobile device connected to iX1600 or iX1500 will be disconnected and scanning will be canceled.

In this case, you can keep the scanned data created before the disconnection by bringing ScanSnap Connect Application active again, however, you cannot continue scanning the rest of the document.
Up to 1,000 pages can be created for a single PDF file.