Scanning Documents (iX100)

The procedure for scanning documents by inserting one document at a time is as follows.

For details about documents that can be scanned, refer to Documents to Scan (iX100).

  1. Open the feed guide of the ScanSnap.
    Opening the Feed Guide
    HINT
    • If you want the document to be ejected from the front of the ScanSnap or when there is not enough space where the document exits the ScanSnap, open the output guide.

      For details about documents that can be scanned with the output guide open, refer to Documents to Scan (iX100).

      Opening the Output Guide
    • How the document is ejected differs as below depending on whether the output guide is open or closed.
      • When the output guide is closed
        When the Output Guide Is Closed
      • When the output guide is open
        When the Output Guide Is Open
    • The [Scan/Stop] button flashes in blue. The button returns to being lit normally when document scanning is enabled.

      In addition, the ScanSnap Manager icon in the notification area located at the far right of the taskbar changes from Not Communicating to Communicating.

  2. Insert the document straight into the feeding section of the ScanSnap, with the scanning side facing up.
    Inserting the Document
    • The document is pulled in until it is set inside the ScanSnap.
    ATTENTION
    • If you specify a standard size instead of selecting [Automatic detection] (default), insert the document by aligning it with the left edge of the feeding section.

      You can configure the scan settings in the ScanSnap Setup Window.

      Aligning the Document
    • When you perform scanning with the output guide closed, leave enough space at the back of the ScanSnap to allow the document to be completely ejected. In addition, when you scan long page documents, hold the scanned documents with your hands to prevent them from falling off the unit where the ScanSnap is placed on.

      Make sure that the area where the document exits the scanner is clear of any obstacles. Otherwise, paper jam may occur.

      Holding a Long Page Document
    • If you scan the following documents with the output guide open, a paper jam may occur and damage the documents. Scan the following documents with the output guide closed.
      • Thick paper (80 g/m2 [20 lb] or heavier)
      • Postcards
      • Business cards
      • Plastic cards
      • Carrier Sheets
      Closing the Output Guide
  3. Press the [Scan/Stop] button on the ScanSnap to start scanning.
    ATTENTION

    Do not perform the following operations during scanning. Doing so will stop scanning.

    • Connect or disconnect the ScanSnap and other USB devices.
    • Close the feed guide.
    • Switch users.
    • Allow the computer to enter sleep mode.
    • The [Scan/Stop] button on the ScanSnap flashes in blue while the documents are being scanned.

      The [ScanSnap Manager - Image scanning and file saving] window appears.

      Scanning
    • When scanning is complete, the [ScanSnap Manager - Image scanning and file saving] window displays a scanning standby status.
      Standby
    HINT

    To continue scanning, insert the next document to be scanned. When the document is inserted, scanning starts automatically.

  4. Press the [Scan/Stop] button on the ScanSnap to finish scanning.
    • The Quick Menu appears.
  5. In the Quick Menu, click the icon of the application to link with ScanSnap Manager.

    For details about linking the following applications with ScanSnap Manager, refer to Useful Usages.

    • Save Documents
    • Save Business Cards
    • Save Receipts
    • Save Photos
    HINT

    The following applications are displayed in the Quick Menu when ScanSnap Organizer and CardMinder are installed.

    • When ScanSnap Organizer is installed

      ScanSnap Organizer

    • When CardMinder is installed

      Scan to CardMinder

    Quick Menu
    • The selected application starts up. For details, refer to the Advanced Operation Guide.
    ATTENTION
    • You cannot start scanning when the Quick Menu is displayed. Either select an icon from the Quick Menu and finish the process, or close the Quick Menu before you perform the next scan.
    • Do not move, delete, or rename scanned images using other applications while the Quick Menu is displayed.
    HINT
    • Clicking Detail displays the description of an application. Placing the mouse cursor over the icon of another application displays the description of the application.
    • Performing a scan while an application that can be automatically linked with is active automatically starts the linkage between ScanSnap Manager and the application.

      For details, refer to the Advanced Operation Guide.