Message List
- All the pages were recognized as blank.
- An error in the ScanSnap's hardware. (0xXXXXXXXX) Turn the ScanSnap off then back on, and try again.
- An error occurred during communication with the cloud service. Wait for a while, and try again.
- An error occurred with the ScanSnap. (0xXXXXXXXX) Turn the ScanSnap off then back on, and try again.
- Are you sure to delete them?
- Cannot connect to the Internet. Check the communication status and try again.
- Cannot download the file because its size has exceeded the downloadable limit (XXXMB).
- Cannot obtain data in the cloud service. Log in with the cloud service again?
- Cannot proceed because the file is being downloaded. Try again after the downloads.
- Cannot proceed because the file is being uploaded. Try again after the uploads.
- Cannot proceed because the file is not yet downloaded. Download the file, and try again.
- Cannot proceed because the folder contains files that are being uploaded. Try again after the uploads.
- Cannot upload the file because its size has exceeded the allowable limit (XXXMB).
- Charge ScanSnap. Battery: xx%
- Communicating with the cloud service... Do you want to stop the file downloads?
- Communicating with the cloud service... Do you want to stop the file uploads?
- Communication error. Wait for a while, and then try again. If the error persists, change the port.
- Connection failed. Check if "Scan to Mobile" on the computer is running properly, and the computer can be connected to your mobile device.
- Connection failed. To connect to the ScanSnap directly, make sure that the ScanSnap is turned on and not being used by another device.
- Connection with ScanSnap was cut off because there was no scan for 15 minutes. Do you want to connect again?
- Could not download the file due to insufficient free disk space. Delete unnecessary files.
- Could not obtain the list in the folder. Check the communication status and try again.
- Could not upload the file due to insufficient disk space in the cloud service. Secure enough space by deleting unnecessary files from the cloud service.
- Do you want to delete the folders?
- Do you want to delete this file?
- Do you want to delete this file?
- Documents have been loaded in the ADF paper chute (cover) and inserted into the manual feeder at the same time. Remove either of the documents. Documents may be jammed. Open the ADF top section and remove the document.
- Documents have not been loaded in the ADF paper chute (cover) or inserted into the manual feeder. Load documents in the ADF paper chute (cover) or insert a document into the manual feeder correctly.
- During syncing, files can be renamed only when you are connected to the Internet. Check the communication status and try again.
- Error in optical system. Turn the ScanSnap off then back on, and try again.
- Failed to communicate with ScanSnap. Check the status of the ScanSnap, and then try again.
- Failed to communicate with the ScanSnap. Try again.
- Failed to communicate with the ScanSnap. Turn the ScanSnap off then back on, and try again.
- Failed to download the file. Check the communication status and try again.
- Failed to download the file. Refresh the list, and try again.
- Failed to receive the file. Check if "Scan to Mobile" on the computer is running properly.
- Failed to upload the file. Refresh the list, and try again.
- Files on the cloud service cannot be deleted because you are not connected to the Internet.
- From your device, you will no longer be able to view any files saved in folders or those that are not yet downloaded. The folders or files in the cloud service, however, will not be deleted even if the connection is cleared.
- Initialize?
- Initialize? To use the ScanSnap Sync option, configure it again after this initialization.
- Load the next document.
- Long page scanning is not available. Select a setting other than [Best] for [Image quality].
- More than one destination was detected. Specify the destination from [Settings] on the [File List] screen.
- Overlapping document detected. If you are discarding the image, return the overlapped documents to the feeder.
- Paper jam occurred. Open the ADF top section and remove the document.
- Paper jam occurred. Open the top cover and remove the document.
- Paper jammed or the maximum scannable length has been exceeded. Open the ADF top section and remove the document.
- Paper jammed or the maximum scannable length has been exceeded. Open the ADF top section and remove the document. For U-turn Scan, adjust the side guides to both edges of the document. To scan a document larger than 360 mm, click the [Stop] button and hold down the [Scan] button on the ScanSnap until it flashes in blue to perform U-turn Scan.
- Paper jammed or the maximum scannable length has been exceeded. Open the ADF top section and remove the document. Select Manual Feeding scan when you scan a document larger than 360 mm (14.17 in.).
- PDF file reached the maximum size (1,000 pages).
- Previewable files were not found. If a file is being uploaded from another device, try again after the uploads.
- Receiving files has been canceled.
- Scanning was stopped because a Carrier Sheet has been detected. Carrier Sheet is not supported.
- Scanning will not start because the inserted document is skewed. The document may be damaged. Remove the document, insert it correctly, and try again.
- ScanSnap is disconnected. Exit the ScanSnap Wireless Setup Tool, and then select ScanSnap from [Connect to:].
- ScanSnap is disconnected. To perform scanning again, select ScanSnap from [Connect to:].
- ScanSnap is turned off because it has not been used for a long time. To re-connect to ScanSnap, turn it on.
- ScanSnap is turned off because its battery is overheated.
- The ADF top section is open. Close the ADF top section.
- The destination could not be found. Check if it is connected to the same network.
- The document sensor(s) are dirty. Open the ADF top section and clean the inside of the ScanSnap.
- The file in the cloud service has been updated. Do you want to send the file on your device?
- The file list could not be refreshed because ScanSnap Sync option is communicating with the cloud service. If there is any file that is being uploaded or downloaded, try again after it has been completed.
- The file may not be displayed properly in the specified application due to insufficient memory. Do you want to transfer the file anyway?
- The file name "xxx" is already used. Select an action.
- The name of the file specified in this device already exists in the cloud service. Select the file you want to keep on both sides.
- The ScanSnap is turned off. Turn the ScanSnap back on, and try again.
- The specified file "xxx" does not exist. Refresh the file list.
- The specified file name already exists in the cloud service. Specify another file name.
- The top cover is opened. Close the top cover.
- There is no paper in the ADF paper chute (cover). Load the document in the ADF paper chute (cover) correctly./ There is no paper in the feed guide. Load the document in the feed guide correctly.
- Unable to open the file because the file format cannot be recognized or is invalid.
- Unable to proceed due to insufficient memory. If this problem persists after exiting unnecessary applications, scan the document at a lower image quality, and then send the file again from your computer.
- Unable to receive the file due to insufficient disk space. Delete unnecessary files, and try again.
- Upload and sync the saved data? Another scan or data preview is available during syncing. Data can be uploaded later from the Preview screen separately.
- Uploading stopped because the file named "xxx" already exists in the cloud service. Check the file in the cloud service, and upload it from the Preview screen.
- When non-alphanumeric characters are included in a file name, it may not be displayed correctly in some e-mail applications. Do you want to rename the file that you are sending?